| Part number | MEC13500A | |
|---|
| EAN | | |
|---|
| Unit | Each | |
|---|
| Details | - The MEC II-series pumps have an automatic protection system. So, for example, if a vane breaks, the rotor and rotor housing can be protected by the rotor—including the flange mountings—being pushed downwards
- Pumps with a "ballast system", identified by B at the end of the item number (e.g. MEC9000MB) have a longer operating time in vacuum operation
- The operating time at -0.95 bar lasts from 8 minutes (standard) up to a maximum of 15 minutes. Continuous operation is permissible at -0.6 bar.
- MEC II-series pumps are supplied with long-life (heat-resistant) vanes as standard
- MEC II-series pumps feature a temperature meter to enable the temperature to be read during operation
- A maintenance hatch can be used to determine the wear condition of the vanes, indicating when the vanes need to be replaced
- Each pump is subjected to a final check in the factory, in which the vacuum, compression and lubrication are tested, among other factors
- A test report relating to the serial number is drawn up for each pump
-
| |
|---|
| Application range | These vacuum pumps with vanes are mainly used in agriculture for filling and emptying slurry tanks | |
|---|
| Properties | These pumps can generate both positive pressure and vacuum | |
|---|
| Technical info | - Composition of the item numbers: MEC = series, 9000 = type, M = indirect drive 540 rpm, A = automatic lubrication, B = ballast system
- On pumps without automatic lubrication (no "A" in the item number), the pump is equipped with a forced lubrication system that is adjusted using dripper nozzles
- On pumps without automatic lubrication, the quantity of lubrication oil is set in the factory and cannot be changed without a tool
- In the case of forced lubrication, as with automatic lubrication, the function must be checked at all times during operation
- Pumps with indirect drive (M) must be driven anti-clockwise
- The direction of rotation is determined when the axle to be driven is aligned with the observer
- If the pump has a direct drive (for example, by a tractor unit) it must be driven anti-clockwise
- Oil to be used for lubricating the vanes: genuine oil from B. P. (item number BP5070)
| |
|---|
| Benefits | - Minimum repair costs thanks to the unique automatic protection system
- As pumps from B.P. are tested, inspected and packaged with the utmost care, trouble-free start-up is 100% guaranteed
| |
|---|
| Nominal volume flow rate | 13845 l/min | |
|---|
| Drive type | PTO 540 rpm | |
|---|
| Direction of rotation | Counter-clockwise (CCW) | |
|---|
| Ballast air injection system | No | |
|---|
| Consists of | - Including PTO shaft cover
- Without pressure relief valve (item 0200013) and vacuum valve (item 0155513)
- The pumps are delivered without lubrication oil (item BP5070)
| |
|---|
| Lubrication system type | Automatic | |
|---|
| Vane type | Long life | |
|---|
| Crash protection system | Yes | |
|---|
| Max vacuum | 0.95 BAR | |
|---|
| Max. relative pressure | 1.5 BAR | |
|---|
| Power requirement for max. pressure | 44 kW | |
|---|
| Power requirement for max. vacuum | 25 kW | |
|---|
| D,PDiameter of hose connection | 100 mm | |
|---|
| Safety valve connection diameter | 2 Inch | |
|---|
| Depression valve connection diameter | 1-1/2 Inch | |
|---|
| ETotal length | 830 mm | |
|---|
| OTotal width | 390 mm | |
|---|
| HHeight | 605 mm | |
|---|
| FMounting holes diameter | 22 mm | |
|---|
| B,LMounting holes distance | | |
|---|
| AMounting holes to shaft end distance | 391 mm | |
|---|
| CMounting holes to end distance | 192 mm | |
|---|
| MShaft centre to left side end distance | 195 mm | |
|---|
| NShaft centre to right side end distance | 195 mm | |
|---|
| IShaft centre to bottom distance | 69 mm | |
|---|
| Shaft diameter | 1-3/8 Inch | |
|---|
| Max. shaft rotation | 540 r/min | |
|---|
| Reservoir capacity | 3.5 l | |
|---|
| Weight | 178 kg | |
|---|
