Part number | MEC9000DL | |
---|
EAN | | |
---|
Unit | Each | |
---|
Details | - The MEC II-series pumps have an automatic protection system. So, for example, if a vane breaks, the rotor and rotor housing can be protected by the rotor—including the flange mountings—being pushed downwards
- Pumps with a "ballast system", identified by B at the end of the item number (e.g. MEC9000MB) have a longer operating time in vacuum operation
- The operating time at -0.95 bar lasts from 8 minutes (standard) up to a maximum of 15 minutes. Continuous operation is permissible at -0.6 bar.
- MEC II-series pumps are supplied with long-life (heat-resistant) vanes as standard
- MEC II-series pumps feature a temperature meter to enable the temperature to be read during operation
- A maintenance hatch can be used to determine the wear condition of the vanes, indicating when the vanes need to be replaced
- Each pump is subjected to a final check in the factory, in which the vacuum, compression and lubrication are tested, among other factors
- A test report relating to the serial number is drawn up for each pump
| |
---|
Application range | These vacuum pumps with vanes are mainly used in agriculture for filling and emptying slurry tanks | |
---|
Properties | These pumps can generate both positive pressure and vacuum | |
---|
Technical info | - Composition of the item numbers: MEC = series, 9000 = type, D = direct drive 1000 rpm, L = anti-clockwise rotation, R = clockwise rotation, A = automatic lubrication, B = ballast system
- On pumps without automatic lubrication (no "A" in the item number), the pump is equipped with a forced lubrication system that is adjusted using dripper nozzles
- On pumps without automatic lubrication, the quantity of lubrication oil is set in the factory and cannot be changed without a tool
- In the case of forced lubrication, as with automatic lubrication, the function must be checked at all times during operation
- The direction of rotation is determined when the axle to be driven is aligned with the observer
- If the pump has a direct drive (for example, by a tractor unit) it must be driven anti-clockwise
- Oil to be used for lubricating the vanes: genuine oil from B. P. (item number BP5070)
-
| |
---|
Benefits | - Minimum repair costs thanks to the unique automatic protection system
- As pumps from B.P. are tested, inspected and packaged with the utmost care, trouble-free start-up is 100% guaranteed
| |
---|
Nominal volume flow rate | 9030 l/min | |
---|
Drive type | PTO 1000 rpm without gearbox | |
---|
Direction of rotation | Counter-clockwise (CCW) | |
---|
Ballast air injection system | No | |
---|
Consists of | - Including PTO shaft cover
- Without pressure relief valve (item 0200013) and vacuum valve (item 0155513)
- The pumps are delivered without lubrication oil (item BP5070)
| |
---|
Lubrication system type | Forced | |
---|
Vane type | Long life | |
---|
Crash protection system | Yes | |
---|
Max vacuum | 0.95 BAR | |
---|
Max. relative pressure | 1.5 BAR | |
---|
Power requirement for max. pressure | 25 kW | |
---|
Power requirement for max. vacuum | 16 kW | |
---|
D,PDiameter of hose connection | 80 mm | |
---|
Safety valve connection diameter | 2 Inch | |
---|
Depression valve connection diameter | 1-1/2 Inch | |
---|
ETotal length | 610 mm | |
---|
OTotal width | 390 mm | |
---|
GHeight | 575 mm | |
---|
FMounting holes diameter | 22 mm | |
---|
B,LMounting holes distance | | |
---|
AMounting holes to shaft end distance | 280 mm | |
---|
CMounting holes to end distance | 141 mm | |
---|
MShaft centre to left side end distance | 195 mm | |
---|
NShaft centre to right side end distance | 195 mm | |
---|
IShaft centre to bottom distance | 164 mm | |
---|
Shaft diameter | 1-3/8 Inch | |
---|
Max. shaft rotation | 1400 r/min | |
---|
Reservoir capacity | 2.5 l | |
---|
Weight | 132 kg | |
---|